Skip to content
OEM / ODM cnc turning factory · Contract manufacturing · Zhejiang, China

CNC Turned Parts: S235JR on the Drawing, Q235B in the Bar

2026年11月17日

CNC turned parts are quoted from three things, and every shop asks for the same three: the drawing, the quantity, and the material. The material almost never arrives as a separate line in the email — it sits in the title block of the drawing, in a box that reads S235JR, A36, SS400 or St37-2.

This page is about one of those names. S235JR is the grade that turns up most often on turned work with no particular job to do: spacers, bushings, studs, brackets, shafts that carry a load but not a hard one. What the four characters declare, which national designations are read as its equivalent, and where those equivalents stop matching is the whole subject.

One correction before anything else. In a machining shop S235JR is bought as bar and tube; where the volume justifies a die, the same steel is cold headed or hot punched. That is a fact about product form rather than about the grade, and it decides more quotes than the chemistry does.

What the four characters in S235JR declare

S235JR is a designation under EN 10025-2, the standard for non-alloy structural steels, and on a drawing for CNC turned parts each character commits to one property. Read left to right, it answers four questions the drawing usually leaves open.

Part What it declares
S Structural steel, non-alloy. The first letter is not decoration: it separates EN 10025 structural grades from cold-forming flat products (DC01, DD11) and from pressure-vessel grades (P265), which carry similar numbers for a different job.
235 Minimum yield strength, 235 MPa — and a minimum at one thickness only. It applies up to 16 mm, then falls to 225 up to 40 mm, 215 up to 80 mm and 195 up to 100 mm. Tensile strength runs 360–510 MPa over 3–100 mm.
J 27 J Charpy V, tested at the temperature the next letter names. Change that letter and the test moves: J0 is 0 °C, J2 is −20 °C, and K2 raises the energy to 40 J.
R Room temperature, +20 °C, as the temperature behind that 27 J. It is the mildest impact class, which is why the grade is cheap and why a part destined for a cold store should not stop here.
1.0038 The numeric steel number under EN 10027-2. One steel, two names; drawings, certificates and mill software each pick whichever fits the box.
+AR / +N Delivery condition, written after the grade: as-rolled is the default, normalized is S235JR+N. The condition changes the structure the tool meets, not the grade on the drawing.

Behind the name sits the chemistry that settles most arguments: carbon capped at 0.17% with no floor, manganese up to 1.40%, phosphorus and sulfur at 0.035% each, and carbon equivalent capped at 0.35% up to 30 mm. That last limit is what a welding procedure turns on, and it is the one GB/T 700 does not state at all.

S235JR bar and tube on a CNC turned parts order

EN 10025-2 covers long products as well as flat, so in Europe S235JR bar is a shelf item rather than a mill project. A CNC turned parts order starts from bar or from tube, and the two carry different designations even when the steel underneath is the same.

Tube is worth a paragraph because the name changes with the product form. Hollow section is ordered to EN 10210-1 as S235JRH — the H is a product-form suffix, not a stronger or weaker steel. A certificate reading S235JR against a tube order is answering a question nobody asked, which is why on a machined tube part the buyer should cite the standard that governs the tube.

Where the volume justifies a die, the part leaves the lathe route altogether. Cold heading wants a killed, fine-grain heat and a soft coil, and the die plus the header only pay for themselves far out: on our floor cold heading starts around 50,000 pieces, hot punching a heated blank in a closed die at 3,000, and turning from bar at 1,000. Below those numbers the die is the expensive component, and turning wins even when the shape looks like a heading job. That ladder belongs to the process, not to the grade — S235JR is an ordinary input to all three.

Then there is what actually sits in the rack. In China the same steel fills every mill warehouse as Q235B carbon steel bar, while S235JR-branded bar is an indent: the mill will roll it, the minimum is a heat, the lead time runs in weeks, and 3,000 bushings consume a fraction of one. So a quote has three honest routes — buy the indent and price its lead time in, buy Q235B and put the substitution on the paper, or decline. The fourth, Q235B shipped against an S235JR print with nothing written down, is the one worth refusing.

 

S235JR material equivalent: eight systems side by side

Buyers ordering CNC turned parts usually already have a table like this in their files. It is a fair starting point and a poor basis for a decision, because it compares names while the standards compare limits. The last column is the one that decides.

System Region Grade Governing standard The limit that actually decides
GB China Q235B / Q235A GB/T 700 The B suffix means impact tested at +20 °C, 27 J; A carries no impact test. Yield 235 MPa, Rm 370–500 MPa, C 0.12–0.20% — a carbon floor that S235JR does not have.
EN EU S235JR (1.0038) EN 10025-2 J = 27 J Charpy, R = tested at +20 °C. C ≤ 0.17%, Mn ≤ 1.40%, P and S ≤ 0.035% each, CEV ≤ 0.35% up to 30 mm.
ASTM USA A36 / A283 Gr.C ASTM A36 / A283 Yield 250 MPa, Rm 400–550 MPa, no impact requirement and no meaningful chemistry ceiling. A36 specifies properties rather than a recipe, which is why it says nothing about machinability.
JIS Japan SS400 / SM400A JIS G 3101 / G 3106 SS400 limits only P and S and requires no Charpy test; yield 245 MPa up to 16 mm. Where toughness is contractual the grade has to be SM400B, not SS400.
DIN Germany, old St37-2 (1.0037) DIN 17100 Superseded in 1994; the old number survives on legacy drawings. Ordering S235JR satisfies an St37-2 callout, and one mill certificate covers both.
BS UK, old 40B BS 4360 Withdrawn in the same 1994 replacement; the chain runs 40B → S235JR. Same steel, same caveat about product form.
ISO International E235B ISO 630 The 1995 designation. ISO 630-2 has since been revised to the S-prefix naming, so confirm which edition the drawing cites before treating E235B as current.
GOST Russia Ст3сп (St3sp) GOST 380 “сп” means killed steel. Yield 245 MPa up to 20 mm, impact at +20 °C. Russian certificates report KCU on a different test piece from the EN Charpy KV, so the two energies are not directly comparable.

Read the last column as a limit rather than a label. Two grades can share a yield strength and still be different steels, and the entry that catches people is the carbon floor in Q235B — the one line S235JR does not have.

Where the equivalents stop being equal

Q235B sets carbon at 0.12–0.20%, so it has a floor. S235JR caps carbon at 0.17% and sets no floor at all: one compliant heat sits at 0.10%, the next at 0.17%, both correct, and the lathe sees both. Manganese runs the other way — 0.30–0.70% against up to 1.40%. Phosphorus and sulfur are 0.045% each against 0.035%, and GB/T 700 states no carbon equivalent where EN 10025-2 caps CEV at 0.35%. Four numbers, and they explain most arguments about whether a substitution held.

The other entries fail in their own ways rather than by degree. A36 specifies properties with no meaningful chemistry ceiling and no impact requirement: in an S235JR vs A36 comparison the tensile line is the only one that agrees, and a weld procedure agrees on nothing. SS400 limits only phosphorus and sulfur and asks for no Charpy test; where toughness is contractual the grade has to be SM400B. St37-2, BS 4360 40B and S235JRG2 are the same steel under withdrawn or superseded numbers — S235JRG2 is the 1993 designation, dropped when EN 10025-2 was published — which is why an old drawing normally costs nothing to satisfy. St3sp reports its impact on the GOST test piece, so a KCU figure cannot be read against a KV figure without conversion.

On CNC turned parts the practical form of that gap is hardness scatter. A spread of 15 to 25 HB between two heats of one grade is ordinary, and on a 12 mm diameter held to 0.02 mm it separates a process that runs unattended from one that needs a tool offset every hundred pieces. S235JR’s tighter sulfur and wider manganese band make the behaviour more repeatable heat to heat — a modest gain on a bracket, a real one on a slender shaft, where deflection at the free end reads as taper instead of a size error.

Neither grade is free-machining, and that is the point most substitutions on CNC turned parts miss. If the drawing calls S235JR because the part carries a load, the chemistry has to follow the drawing. If it calls S235JR out of habit and the part is a spacer with no load path, the answer is not a better structural grade — it is 20# or a resulfurized grade, cheaper and cut twice as fast. The stainless version of the same decision runs through our custom turned 304 parts, where the free-cutting grade is 303.

Four checks before a substitute grade goes on the drawing

Check Look at It fails when
Strength at the section The thickness band the drawing falls into, not the headline yield. Every system drops yield as thickness rises: 235 MPa to 16 mm, then 225, then 215. The 235 is quoted from a thin-stock table and the part is machined from 50 mm bar.
Impact, as a number Energy and temperature together. S235JR is 27 J at +20 °C; A36 and SS400 carry no default Charpy requirement at all. The part goes into a cold-chain or outdoor application and the substitute was chosen on strength alone.
Chemistry floor and CEV Whether the substitute has a carbon floor, how wide its manganese band runs, and whether the standard states a carbon equivalent at all. The part is welded and the Q235B heat lands at 0.40 CEV, where the S235JR drawing assumed no preheat.
What the paper says The grade on the mill certificate, the heat number, and whether it is a 3.1 or a 2.2. The parts are right and the file cannot prove it, which fails an audit rather than a test.

The order of those four matters more than the list. Impact comes first because it is the only one that cannot be fixed later: strength can be argued and chemistry re-tested, but a part in a cold application without the test is one nobody can sign. Chemistry second, because it drives both the weld and the lathe. Certificate third, because it costs nothing at order and everything after shipment.

What the certificate must say on CNC turned parts

If the grade on the quote differs from the grade on the print, the paperwork is the only thing that makes the substitution legitimate. EN 10204 3.1 is signed by a representative of the mill’s inspection department who is independent of production, where 2.2 is a statement of compliance with no test results. A 3.1 naming S235JR with a heat number, matched to Q235B bar from that heat, is a defensible record, because the two are one steel under two national numbers. Japanese material arrives as the 3.1B equivalent; Russian material arrives as a GOST certificate that states KCU rather than KV.

Then our own records, which cover what the mill certificate does not: a dimensional report from first article and sampling, a thread gauge record made after plating rather than before, and a plating certificate from the line. Hardness readings come back with the heat-treat report — that step goes to a workshop we have used for years, and the report arrives with the batch instead of being reconstructed afterwards. Where the part is quenched and tempered rather than as-rolled, the route behind it is on the heat-treat route in the background.

What none of this fixes is a customer who needs the certificate to say S235JR when the bar was Q235B. No document converts one grade into another. Either the drawing is revised, or a deviation is raised and accepted before shipment — and the second is normal engineering practice, not a favour. We are a turning factory rather than a trading company, so on CNC turned parts the bar, the lathe and the gauge sit in the same building, and the grade on the certificate is the grade on the machine.

What to send with an RFQ for CNC turned parts

A drawing and a STEP file cover the geometry of a CNC turned part. The rest of the list is what decides the price.

On the RFQ Why it changes the answer If it is missing
Grade, standard number, edition “S235JR” and “S235JR to EN 10025-2” are different instructions once the part is welded or impact tested. We quote the grade we can buy and name it.
Product form and bar size A plate grade that is not stocked as bar turns a one-week job into a mill indent. We assume bar of the nearest stocked grade.
Impact energy and temperature 27 J at −20 °C is a different grade from 27 J at +20 °C, and a different price. We quote the +20 °C class, which is the common one.
Thread standard and class NPT, BSPP and metric are not interchangeable, and a 6g thread after plating is a different callout from 6g before. We ask before quoting rather than after the first article.
Finish, and what it must survive A salt-spray figure sets the plating class, and the class decides whether the thread has to be allowed for. The callout itself is in how a plating callout is written. We quote standard zinc and flag that it may not hold outdoors.
Volume, and whether lot one is a pilot It picks the route: turned from bar at 1,000 pieces, hot punched at 3,000, cold headed at 50,000. We quote turning and note where a die would be cheaper.
Acceptance and documents Which report, to which standard, and whether a third-party witness is needed — some of that we buy in rather than issue. You get a 3.1, a dimensional report and a CoC.

The same question comes up on the pipe side, where a carbon grade has to survive a finish as well as a load — that comparison is in the carbon steel pipe fitting range — and parts that start as a shape rather than a bar are on when the shape has to start as a forging.

For a buyer holding two grade names and no metallurgist, the short version for a CNC turned parts order is this: send the drawing, the standard number, the impact requirement and the quantity, and expect the quote to name the grade it is priced on. A supplier that will not name the grade is not protecting anyone from a substitution; it is doing the substitution quietly. Parts up to 300 × 300 mm come off our own lathes — turning, milling, drilling and tapping in one clamping, gantry-robot loading, and a grinder in the same building for anything past turning — while welding, plating and heat treatment go outside, and every step that leaves the building is named in the quote. What the workshop runs end to end is on the machining services page.

FAQ

Frequently asked questions

01Q1. Can you supply S235JR bar instead of Q235B for a turned part?

A: Yes, as a mill indent rather than off the shelf. S235JR is a standard stock item in Europe and an indent item here: the mill will roll it, the minimum is a heat, and the lead time runs in weeks. On a 3,000-piece run that cost is hard to justify, which is why the quote usually names Q235B and says so, rather than quoting S235JR and shipping something else.

02Q2. What do the letters in S235JR actually stand for?

A: Four commitments. S is structural, non-alloy steel; 235 is the minimum yield strength in MPa, valid up to 16 mm and lower above it; J is 27 J Charpy V; R is room temperature, +20 °C, as the test temperature. Written after the grade, +AR or +N states the delivery condition, as-rolled or normalized, and 1.0038 is the same steel under the numeric system.

03Q3. Is S235JRH the same steel as S235JR?

A: The steel is the same; the product standard is not. Hollow section and tube are ordered to EN 10210-1, where the H suffix marks the product form. On a part machined from tube, the buyer should cite the tube standard, because a mill certificate issued to EN 10025-2 covers plate, strip and bar rather than the hollow section that was actually cut.

04Q4. My drawing says SS400. Does Q235B meet it?

A: Usually on strength, not automatically on paper. SS400 requires yield of 245 MPa up to 16 mm and limits only phosphorus and sulfur, with no Charpy requirement; Q235B gives 235 MPa and does require 27 J at +20 °C, which is the stricter of the two on toughness. What Q235B cannot do is arrive with a JIS certificate, so if the drawing names JIS G 3101 the documents are the blocker, not the steel.

05Q5. Can you issue a certificate that says S235JR when the bar was Q235B?

A: No, and no supplier should. The mill certificate states the grade the mill rolled and the heat number; nobody in the chain can convert one designation into another on paper. The two routes are a drawing revision or a deviation accepted before shipment, and both are ordinary engineering practice rather than a favour.

06Q6. Does the steel grade really change the tolerance you can hold on a turned part?

A: Yes, through hardness scatter rather than through the tolerance itself. A 15 to 25 HB spread between two heats of the same structural grade moves cutting force and tool wear, and on a 12 mm diameter held to a 0.02 mm band that shows up as taper or as a size drift through the run. Specifying one heat for the order does more than tightening the drawing.

07Q7. My drawing still calls St37-2 or S235JRG2. Is that a problem?

A: Not for supply. St37-2 was withdrawn in 1994 and S235JRG2 is the 1993 designation that EN 10025-2 replaced; both numbers survive on legacy drawings, and a mill certificate for S235JR covers the same steel under all three names. The thing to check is not the name but the product form, because a plate grade on a drawing often has to be bought as bar.

08Q8. Is A36 a safe substitute for S235JR on a turned part?

A: On strength it is close — 250 MPa yield against 235 — but A36 has no impact requirement and no meaningful chemistry ceiling, so it tells you nothing about toughness or machinability. For a part in a cold or outdoor application the difference is the whole point of the specification. For an indoor bracket that happens to be turned, it is usually fine, and it should still be written on the quote.

Quick inquiry

Send an inquiry to our team

Tell us material, thread, quantity, and requirements. After submit, email drawings to info@sspipefitting.com if needed.

Article

CNC Turned Parts: S235JR on the Drawing, Q235B in the Bar